DIY Needle Felting Project: Bird on a Branch Coaster

I went bright for this coaster. It’s a different look from the rustic coaster that I posted last week, but I had just as much fun making it.

Needle felting let’s you shape wool like you would clay, but since the wool doesn’t stick to itself on it own, we use a barbed needle to make it adhere to itself. As the needle goes in and out of the wool, the barbs catch the fibers and intertwine them. It’s a simple process, but the needles are sharp so I can’t recommend needle felting for kids under 9 years old. I’ve pricked myself several times.

 

DIY Need Felted Coaster Tutorial

Supplies:

Sponge

1/4 -1/2 oz Wool Roving (unspun wool) colors: magenta, brown, blue, green, and yellow

Felting needle

Extra paper or a magazine to protect your work surface from inadvertent pokes

1. For this project I used 1/4 ounce of wool roving in a 14 inch long strip to make a coaster 3 inches diameter. The size and thickness of your finished coaster will depend on the amount of wool you use. Roll a strip of your main color roving into a spiral (for this coaster, magenta).

DSCN4027

The resulting circle should have a diameter an inch or so larger than the desired diameter for your finished coaster. It should be around an 1 1/2 thick. As you felt the wool with your felting needle, the wool will compress.

DSCN3941 DSCN3942

2. Place your wool roving on a sponge. Insert your needle all over the surface of the wool to achieve even felting. Do this for a minute or so on one side. They flip and repeat. You do not want to let your needle embed deeply in the sponge. This will cause the wool to adhere to the sponge. Instead, consider the sponge to be a soft “landing pad” for the tip of your needle.

DSCN3944 DSCN3946

3. The wool will have begun to cling to itself a little bit. Now insert your needle into the outer rim of your coaster. This will involve inserting your needle horizontally into the wool. Circle around the rim several times. This will intertwine the wool from the opposite direction and will make your coaster stronger.

DSCN3947

4. Check to make sure the diameter of your coaster is where you want it. If it is two wide, you can needle around the outer rim of the coaster several more times.

DSCN3951

5. Now needle the top and bottom of the coaster, flipping every couple of minutes. In 15-20 minutes, you will have a firm, fairly smooth surface. Remember to insert your needle all over the surface. Don’t neglect the edges.

DSCN3953 DSCN3964

6. To make the main branch, take a wisp of your brown roving and roll it between your fingers. Lay it on the coaster and needle along it until it adheres. This will create an indent in the coaster. To counter that, needle all over the coaster again.

DSCN4008DSCN4011DSCN4012  DSCN4009

7. To make your branch stand out a bit from the rest of the coaster, add another layer of roving and insert you needle along the outside edge of the branch.

DSCN4023

 

7. Add another branch or two

to the top of the main branch in a similar manner.

DSCN4014

8. Add a couple of green leaves to the tips of your branches by rolling bits of roving between your fingers and then shaping them into leaves as you felt them into place.

DSCN4016

9. Form a bit of blue roving into the basic shape of a bird, lay it on your coaster, and needle felt into place. Add a bit of yellow roving to the tip of the bird’s head for a beak. Add another layer of wool and insert your needle around the edge of the bird to give it a bit of dimension.

DSCN4018DSCN4021

 

10. Relax with a glass of lemonade and no fear for your end table.

DSCN4040

 

Looking for needle felting supplies? This project is available as a kit in the Catching Eddies Etsy shop.

Leave a Reply

Your email address will not be published. Required fields are marked *